ISO IEC 24700-2005 pdf – Quality and performance of office equipment that contains reused components

ISO IEC 24700-2005 pdf – Quality and performance of office equipment that contains reused components.
3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 17050, EN 60950, CISPR 14, CISPR 22, CISPR 24, IEC 61000, ISO 9001 and ISO 14001 and the following, apply. 3.1 Conformity assessment: Any activity concerned with determining directly or indirectly that relevant requirements are fulfilled. 3.2 Supplier’s declaration: Procedure by which a supplier gives written assurance that a product, process or service conforms to specified requirements. NOTE The supplier is the party that supplies the product, process or service and may be a manufacturer, distributor, importer, assembler, service organization, etc. In order to avoid any confusion, the expression “self-certification” should not be used. 3.3 Office equipment: Printers, copying equipment, digital scanners, facsimile equipment and systems composed of combinations of these types of equipment. 4 Office equipment requirements 4.1 Performance The equipment must be assured, by the original equipment manufacturer or authorized party, to perform per the original product design specifications as documented by the original manufacturer in its product literature and guaranties. This means that the equipment, when comprised of reused parts should have the same cosmetic, functional and performance characteristics as the equipment when comprised of all new parts. 4.2 Upgrades The equipment must be manufactured using components that, if functionally critical, represent the most up-to- date specification of the components, regardless of whether or not the components are new or reused. NOTE This means that the equipment that contains reused parts must be upgraded with components that significantly affect the function of the equipment. An example might be an upgraded electronic board, with changes that fix a problem discovered soon after product introduction.
4.3 Testing The equipment must be tested using the equivalent procedures as defined by the manufacturer regardless of whether or not the product contains all new components or if it contains reused components. 4.4 Quality If the equipment is originally manufactured in an ISO 9001 certified factory, then this condition must be maintained. Factory certification to the ISO 9001, Quality management systems — Requirements may ensure that the product conforms to the product’s established design. 4.5 Safety and electromagnetic emissions The equipment must meet, at a minimum, the requirements of the international product safety International Standard IEC 60950, Safety of Information Technology Equipment. The equipment must also meet, if applicable to the equipment type and required by the market in which the product is sold, the requirements of the following standards: CISPR 14, Electromagnetic Compatibility — Requirements for household appliances, electric tools and similar apparatus — Part 1: Emission — Product Family Standard; Part 2: Immunity — Product family standard. CISPR 22, Information Technology Equipment — Radio Disturbance Characteristics — Limits and methods of measurement. CISPR 24, Information Technology Equipment — Immunity Characteristics — Limits and methods of measurement. IEC 61000, Electromagnetic compatibility (EMC) — Part 3-2: Limits — Limits for harmonic current emissions (equipment input current <= 16 A per phase). IEC 61000, Electromagnetic compatibility (EMC) — Part 3-3: Limits — Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection. 4.6 Warranties/Guarantees The equipment’s warranties and guaranties must apply equally to equipment manufactured of all new components and to equipment that contains reused components.
5 Demonstration of conformance 5.1 Supplier Declaration of conformity When it is required that a supplier demonstrate conformance with the requirements of this International Standard and the normative references in 2.1, the supplier shall complete Annex A, “Supplier’s declaration of conformity in accordance with ISO/IEC 17050-1.” 5.2 Documentation Documentation prepared in meeting the requirements of the normative references in 2.1 shall be available upon request in accordance with ISO/IEC 17050-2. Other documentation prepared in meeting requirements specifically pertaining to the characteristics of office equipment shall also be available upon request. NOTE Characteristics of office equipment are specified by ISO standards such as ISO/IEC 11159, and ISO/IEC 11160.