IEC 60092-360-2014 pdf – Electrical installations in ships – Part 360: Insulating and sheathing materials for shipboard and offshore units, power, control, instrumentation and telecommunication cables.
2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60092-350:— 1 , Electrical installations in ships – Part 350: General construction and test methods of power, control and instrumentation cables for shipboard and offshore applications IEC 60754-1 , Test on gases evolved during combustion of materials from cables – Part 1: Determination of the halogen acid gas content IEC 60754-2, Test on gases evolved during combustion of materials from cables – Part 2: Determination of acidity (by pH measurement) and conductivity IEC 60684-2:201 1 , Flexible insulating sleeving – Part 2: Methods of test IEC 6081 1 -201 , Electric and optical fibre cables – Test methods for non-metallic materials – Part 201: General tests – Measurement of insulation thickness IEC 6081 1 -202:201 2, Electric and optical fibre cables – Test methods for non-metallic materials – Part 202: General tests – Measurement of thickness of non-metallic sheath IEC 6081 1 -401 , Electric and optical fibre cables – Test methods for non-metallic materials – Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven
IEC 6081 1 -403, Electric and optical fibre cables – Test methods for non-metallic materials – Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds IEC 6081 1 -404, Electric and optical fibre cables – Test methods for non-metallic materials – Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths IEC 6081 1 -409, Electric and optical fibre cables – Test methods for non-metallic materials – Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths IEC 6081 1 -501 , Electric and optical fibre cables – Test methods for non-metallic materials – Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds IEC 6081 1 -505, Electric and optical fibre cables – Test methods for non-metallic materials – Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths IEC 6081 1 -507, Electric and optical fibre cables – Test methods for non-metallic materials – Part 507: Mechanical tests – Hot set test for cross-linked materials IEC 6081 1 -508, Electric and optical fibre cables – Test methods for non-metallic materials – Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths IEC 6081 1 -509, Electric and optical fibre cables – Test methods for non-metallic materials – Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test) ISO 1 81 7, Rubber vulcanised – Determination of the effect of liquids ISO 48:2007, Rubber, vulcanised or thermoplastic – Determination of hardness (hardness between 10 IRHD and 100 IRHD) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 variation difference between the median value after ageing and the median value without ageing Note 1 to entry: Variation is expressed as a percentage between the median value before and after ageing. 3.2 median value when several test results have been
3.3.2 HEPR hard ethylene-propylene rubber cross-linked high modulus or hard grade compound in which the elastomer is an ethylene- propylene, EPDM or an equivalent synthetic elastomer providing a compound compliant with type HEPR Note 1 to entry: This note applies to the French language only. 3.3.3 XLPE cross-linked polyethylene cross-linked compound in which the polymer is a low density polyethylene or equivalent synthetic polymer providing a compound compliant with type XLPE Note 1 to entry: This note applies to the French language only. 3.3.4 HF 90 cross-linked polyolefin halogen-free cross-linked compound in which the polymer is a polyolefin or equivalent synthetic polymer not containing halogens providing a compound which is compliant with type HF 90 3.3.5 S 95 cross-linked silicone rubber compound based on a polysiloxane elastomer which, when cross-linked, is compliant with type S95. 3.4 types of sheathing compounds 3.4.1 SE polychloroprene rubber cross-linked compound in which the elastomer is a polychloroprene (PCP) or equivalent synthetic elastomer providing a compound which is compliant with type SE 3.4.2 SH chlorosulphonated polyethylene rubber chlorinated polyethylene rubber cross-linked compound in which the characteristic constituent is a synthetic chlorinated rubber, e.g., chlorosulphonated polyethylene (CSP) or chlorinated polyethylene (CPE), which is compliant with type SH Note 1 to entry: This note applies to the French language only. 3.4.3 SHF 2 halogen-free rubber cross-linked compound in which the polymer is a polyolefin or equivalent synthetic polymer, not containing halogens, providing a compound which is compliant with type SHF 2
www.findfreestandards.com