ASME-SA29- 2010 pdf download

ASME-SA29- 2010 pdf download

ASME-SA29- 2010 pdf download.SPECIFICATION FOR STEEL BARS, CARBON AND ALLOY, HOT-WROUGHT, GENERAL REQUIREMENTS FOR. 3.1.1.1 Rounds — 7 ⁄ 32 to 10.0 in. [5.5 to 250 mm], inclusive, 3.1.1.2 Squares — 7 ⁄ 32 to 6.0 in. [6 to 160 mm], inclusive, 3.1.1.3 Round-Cornered Squares — 7 ⁄ 32 to 8.0 in. [6 to 200 mm], inclusive, 3.1.1.4 Flats —...

ASME NOG-1 – 2010 pdf download

ASME NOG-1 – 2010 pdf download

ASME NOG-1 – 2010 pdf download.Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder). 1144 Humidity (a) The purchase specification shall specify the humidity conditions in the area where the crane operates. (b) The crane shall be designed to withstand the effects of the specified humidity, or the limitations of the crane’s design concerning the humidity...

ASME PCC-1–2010 pdf download

ASME PCC-1–2010 pdf download

ASME PCC-1–2010 pdf download.Guidelines for Pressure Boundary Bolted Flange Joint Assembly. 7 LUBRICATION OF “WORKING” SURFACES 5 Lubrication reduces the coefficient of friction and results in less required torque to achieve a given tension, improves the consistency of achieved load from bolt to bolt within the joint, and aids in the subsequent disas- sembly of the fasteners. The reference torque...

ASME PTB-3-2010 pdf download

ASME PTB-3-2010 pdf download

ASME PTB-3-2010 pdf download.Section VIII – Division 2 Example Problem Manual. The subject of Examination Groups is covered in Part 7, paragraph 7.4.2. The assignment of a welded joint to a particular Examination Group is dependent on the manufacturing complexity of the material, the maximum thickness, the welding process, and the selected weld joint efficiency. The Examination Groups are defined...

ASME PTC 19.3 TW-2010 pdf download

ASME PTC 19.3 TW-2010 pdf download

ASME PTC 19.3 TW-2010 pdf download.Thermowells. 4-1 CONFIGURATIONS Figure 4-1-1 shows a schematic diagram of a ther- mowell, along with its characteristic dimensions. Typical thermowell attachment confgurations include threaded, socket weld, weld-in, lap-joint (Van Stone), and integral-fanged as shown in Figs. 4-1-2, 4-1-3, and 4-1-4 (see also Table 4-1-1). These fgures are representa- tive of common practice but do not...

ASME A17.2-2010 pdf download

ASME A17.2-2010 pdf download

ASME A17.2-2010 pdf download.Guide for Inspection of Elevators, Escalators, and Moving Walks Includes Inspection Procedures for Electric Traction and Winding Drum Elevators, Hydraulic Elevators, Inclined Elevators, and Escalators and Moving Walks. CSA B44.1/ASME A17.5 Elevator and Escalator Electrical Equipment. This Code contains requirements for obtaining, labeling, and listing electrical equipment for elevators, escalators, moving walks, dumbwaiters, material lifts, platform lifts,...

ASME B107.600-2008 pdf download

ASME B107.600-2008 pdf download

ASME B107.600-2008 pdf download.Screwdrivers. 1 SCOPE This Standard covers straight handle-type screwdriv- ers of flat tip design intended for manual operation in driving or removing screws with slotted recesses. The screwdrivers are of the types normally used by cabinet- makers, carpenters, sheet metal workers, production workers, mechanics, etc. The intention is to specify per- formance rather than design detail. Inclusion...

ASME B107.400-2008 pdf download

ASME B107.400-2008 pdf download

ASME B107.400-2008 pdf download.Striking Tools. 1 SCOPE This Standard provides performance and safety requirements for hatchets (that are intended specifically for use in driving unhardened nails or striking wood products, or both; cutting, notching, and shaping wood products or wall board products, or both; cutting, spac- ing, and aligning soft roofing products, and pulling unhardened nails when the tool is...

ASME BPE-2009 pdf download

ASME BPE-2009 pdf download

ASME BPE-2009 pdf download.Bioprocessing Equipment. GR-4.1 Inspector’s Delegate Inspector’s Delegate qualifications shall be in accor- dance with the requirements listed herein. The employer ofthe Inspector’s Delegate shall have documented train- ing and qualification programs to ensure the qualifica- tions and capabilities of personnel are met. The capabilities requirements are listed in Table GR-1. It is required that a capability listed...

ASME CSD-1–2009 pdf download

ASME CSD-1–2009 pdf download

ASME CSD-1–2009 pdf download.Controls and Safety Devices for Automatically Fired Boilers. CW-140 Requirements for Water Level Controls for High-Pressure Steam Boilers (a) Each automatically fired, high-pressure steam boiler, except miniature boilers, shall have at least two automatic low-waterfuelcut-offdevices. Wheninstalled external to the boiler, each device shall be installed in individual chambers (water columns), which shall be attached to the boiler...