API MPMS 4.7 2008 pdf download.Manual of Petroleum Measurement Standards Chapter 4—Proving Systems Section 7—Field Standard Test Measures. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. API Manual of Petroleum Measurement Standards (MPMS) Chapter 1, Vocabulary API MPMS Chapter 4.2, Displacement Provers API MPMS Chapter...
API MPMS 5.1-2005 pdf download.Manual of Petroleum Measurement Standards Chapter 5—Metering Section 1—General Considerations for Measurement by Meters. 5.1.1 Introduction API MPMS Chapter 5 covers the general installation and operation of meters and accessory equipment, without respect to the arrangements necessary to meet special problems. The guidelines are common to all metering systems, but appropri- ate precautions should be taken...
API MPMS 5.4-2005 pdf download.Manual of Petroleum Measurement Standards Chapter 5—Metering Section 4—Accessory Equipment for Liquid Meters. 5.4.1 Introduction API Chapter 5.4 of the Manual of Petroleum Measurement Standards is intended to be a guide for the selection and application of accessory equipment that is used with liquid hydrocarbon meters to obtain accurate measurements and optimum service life. Accessory equipment...
API MPMS 10.8-2005 pdf download.Manual of Petroleum Measurement Standards Chapter 10—Sediment and Water Section 8—Standard Test Method for Sediment in Crude Oil by Membrane Filtration. 5. Apparatus 5.1 Funnel and Filter Support Assembly—Use an assembly designed to hold 47-mm diameter filters as was used in the development of this test method (see Fig. 1). 5 5.1.1 Filter Funnel—Use a filter...
API MPMS 11.5.2 2009 pdf download.Manual of Petroleum Measurement Standards Chapter 11—Physical Properties Data Section 5—Density/Weight/Volume Intraconversion Part 2—Conversions for Relative Density (60/60 °F). Implementation Guidelines This revised standard is effective upon the date of publication and supersedes the applicable parts of API MPMS Ch. 11.1-1980, Volumes XI/XII. However, due to the nature of the changes in this revised standard,...
API MPMS 22.2-2012 pdf download.Manual of Petroleum Measurement Standards Chapter 22—Testing Protocol Section 2—Differential Pressure Flow Measurement Devices. 1.0 Introduction This document defines the testing and reporting protocols for flow measurement devices based on the detection of a pressure differential that is created by the device in a flowing stream. This protocol is designed to supply industry with a comparable...
API PUBL 4711-2001 pdf download.Methods for Determining Inputs to Environmental Petroleum Hydrocarbon Mobility and Recovery Models. 4.1 Sample Collection Sediments – Analysis of soil properties at a laboratory scale begins with obtaining representative soil samples. Ideally, soil samples should be undisturbed. This reflects the fact that parameters of interest are dependent on the geometry of pore bodies and throats. Preservation...
API Publ 4712-2001 pdf download.Gas-Fired Steam Generator— Test Report Site C Characterization of Fine Particulate Emission Factors and Speciation Profiles from Stationary Petroleum Industry Combustion Sources. In 1997, the United States Environmental Protection Agency (EPA) promulgated new ambient air standards for particulate matter, including for the first time particles with aerodynamic diameters smaller than 2.5 micrometers (PM2.5). There are few...
API RP 2SM-2001 pdf download.Recommended Practice for Design, Manufacture, Installation, and Maintenance of Synthetic Fiber Ropes for Offshore Mooring. 3.3.4 Durability and Fatigue Factors which may limit the life of synthetic fiber ropes for deepwater mooring and which should be checked include hydrolysis, heating and internal abrasion, tension-tension fatigue and axial compressive fatigue. The possibility of creep rupture was commented...
API RP 2Z-2005 pdf download.Recommended Practice for Preproduction Qualification for Steel Plates for Offshore Structures. 1 Introduction 1.1 PURPOSE The purpose of these recommendations is to provide the purchaser with information which can be used to minimize the amount of time and testing necessary to prepare and certify fabrication welding procedures (and to assure that the steel to be supplied...