API St 600-2021 pdf download

API St 600-2021 pdf download.Steel Gate Valves—Flanged and   Butt-welding Ends, Bolted Bonnets.
ASME B1.1, 1 Unifed Inch Screw Threads (UN and UNR Thread Form) ASME B1.5, Acme Screw Threads ASME B1.8, Stub Acme Screw Threads ASME B1.12, Class 5 Interference—Fit Thread ASME B1.13M, Metric Screw Threads: M Profle ASME B16.5, Pipe Flanges and Flanged Fittings NPS 1/2 through NPS 24 Metric/Inch ASME B16.10, Face-to Face and End-to-End Dimensions of Valves ASME B16.25, Buttwelding Ends ASME B16.34, Valves—Flanged, Threaded and Welding End ASME B16.47, Large Diameter Steel Flanges, NPS 26 Through NPS 60 Metric/Inch Standard ASME B18.2.2, Nuts for General Applications: Machine Screw Nuts, Hex Flange, and Coupling Nuts (Inch Series) ASME B18.2.6M, Metric Fasteners for Use in Structural Applications ASME B31.3, Process Piping ISO 5210 2, 2 Industrial valves—Multi-turn valve actuator attachments ISO 5752, Metal valves for use in fanged pipe systems—Face-to-face and centre-to-face dimensions MSS SP-91 3, 3 Guidelines for Manual Operation of Valves MSS SP-102, Multi-Turn Valve Actuator Attachment—Flange and Driving Component Dimensions and Performance Characteristics MSS SP-134, Valves for Cryogenic Service, including Requirements for Body/Bonnet Extensions MSS SP-144, Pressure Seal Bonnet Valves 3? Terms? and? Defnitions For the purposes of this document, the following defnitions apply.
3.2 DN A numeric designation of size that is common for components used in a piping system and used for reference purposes, comprising the letters “DN” followed by a dimensionless number indirectly related to the physical size of the bore or outside diameter of the end connection as appropriate. The dimensionless number following “DN” does not represent a measurable value and is not used for calculation purposes, except where specifed. 3.3 NPS A numeric designation of size that is common for components used in a piping system and used for reference purposes, comprising the letters “NPS” followed by a dimensionless number indirectly related to the physical size of the bore or outside diameter of the end connection as appropriate. The dimensionless number may be used as a valve size identifer without the prefx “NPS” The dimensionless size identifcation number does not represent a measurable value and is not used for calculation purposes. 3.4 shell Comprised of the body, bonnet, and body-bonnet bolting that constitute the pressure boundary of an API 600 valve. 4 Pressure/Temperature Ratings 4.1 Pressure/temperature ratings shall be in accordance with those specifed in the tables of ASME B16.34 for standard class for the applicable material specifcation and the applicable class. 4.2 Restrictions of temperature and concurrent pressure, or pressure and concurrent temperature (e.g., those imposed by special soft seals or special trim materials), shall be marked on the valve identifcation plate (see Section 8). 4.3 The temperature for a corresponding pressure rating is the maximum temperature of the pressure- containing shell of the valve. In general, this temperature is the same as that of the contained fuid. The use of a pressure rating corresponding to a temperature other than that of the contained fuid is the responsibility of the user.
5.1.2 The weld end preparation in butt-welding end valves (see 5.3.2) shall not reduce the body wall thickness to less than the values specifed in 5.1.1 within a region closer than t m to the outside surface of the body neck, measured along the run direction. The transition to the weld preparation shall be gradual and the section shall be essentially circular through the entire length of the transition. Sharp discontinuities or abrupt changes in section in areas that infringe into the transition shall be avoided, except that test collars or bands, either welded or integral, are allowed. In no case shall the thickness be less than 0.77t m at a distance of 2t m from the weld end. 5.2 Bonnet Wall Thickness The minimum bonnet wall thickness at the time of manufacture, except for the neck extension that contains the packing, shall be t m as given in Table 1. For the neck extension, the local minimum wall thickness shall be based on the local diameter, e.g., the inside diameter of the stem bore or packing box bore, and shall be in accordance with the valve body neck rules of ASME B16.34. 5.3 Body Dimensions 5.3.1 Flanged Ends 5.3.1.1 Body end fanges shall comply with the dimensional requirements of ASME B16.5 for sizes up to and including DN 600 (NPS 24). For sizes over DN 600 (NPS 24), body end fanges shall comply with the dimensional requirements of ASME B16.47 Series A or Series B as specifed by the purchaser. Unless otherwise specifed, raised face end fanges shall be provided. The purchaser may specify a fange facing fnish other than that specifed in ASME B16.5 or ASME B16.47, as applicable.