API SPEC 7K-2010 pdf download

API SPEC 7K-2010 pdf download.Drilling and Well Servicing Equipment
API Specification 16A, Specification for Drill-through Equipment AGMA 2004-C08 1 , Gear Materials, Heat Treatment and Processing Manual AISC 360-05 2 , Specification for Structural Steel Buildings ASME B1.1-2003 3 , Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.2, Gages and Gaging for Unified Inch Screw Threads ASME B16.34, Valves Flanged, Threaded, and Welding End ASME B30.9, Slings ASME B31.3, Process Piping ASME Boiler and Pressure Vessel Code, Section V: Nondestructive Examination ASME Boiler and Pressure Vessel Code, Section VIII, Division 1, Rules for Construction of High Pressure Vessels ASME Boiler and Pressure Vessel Code, Section VIII, Division 2: Rules for Construction of High Pressure Vessels – Alternative Rules ASME Boiler and Pressure Vessel Code, Section IX: Welding and Brazing Qualifications ASNT SNT-TC-1A 4 , Recommended Practice for Personnel Qualification and Certification in Nondestructive Testing ASTM A370 5 , Standard Test Methods and Definitions for Mechanical Testing of Steel Products ASTM A388, Standard Practice for Ultrasonic Examination of Steel Forgings ASTM A751, Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products ASTM A770, Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications ASTM E4, Standard Practices for Force Verification of Testing Machines ASTM E125, Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings
MSS SP-53 10 , Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components—Magnetic Particle Examination Method MSS SP-55, Quality Standard for Steel Castings for Valves, Flanges and Fittings and Other Piping Components— Visual Method for Evaluation of Surface Irregularities NFPA T2.12.10 R1 11 , Recommended Practice—Hydraulic Fluid Power—Systems and Products—Testing General Measurement Principles and Techniques 3 Terms, Definitions, and Acronyms For the purposes of this document, the following terms, definitions and abbreviated terms apply. 3.1 Terms and Definitions 3.1.1 BOP handling systems and equipment Equipment designed for the purpose of storing, lifting, lowering, and transporting BOP stacks used on drilling and/or production facilities or rigs. 3.1.2 BOP stack BOPs assembled as a unit, including all attachments. 3.1.3 critical area Highly stressed regions on a primary load-carrying component.
3.1.5 design safety factor DSF Factor to account for a certain safety margin between the maximum allowable stress and the minimum specified yield strength of the material. 3.1.6 design verification test Test undertaken to validate the integrity of the design calculations used. 3.1.7 drilling liquids Liquid solutions (referred to as mud) conveyed at high pressure through the high-pressure mud piping system, mud standpipe, rotary hose, rotary swivel stem, drill string, and drill bit to accommodate the drilling process. NOTE For the purpose of this specification, drilling liquids do not include fluids containing pressurized air or gasses of any kind. 3.1.8 dynamic load Load applied to the equipment due to acceleration effects. 3.1.9 end connector A fitting located at the end of a hose assembly featuring line pipe threads that allows a hose assembly to be connected to a piping system. EXAMPLE A flange or hub, as specified in API 6A, or a hammer lug union that is butt-welded to, or is manufactured as an integral part of the hose coupling material. NOTE 1 See API 5B for line pipe thread specifications. NOTE 2 See Figure 11. 3.1.10 equivalent round ER Standard for comparing variously shaped sections to round bars, used in determining the response to hardening characteristics when heat treating low-alloy and martensitic corrosion-resistant steels. 3.1.11 hazardous area or zone A location where fire or explosion hazards may exist due to flammable gases or vapors, flammable liquids, combustible dust, or ignitable fibers or flyings. 3.1.12 high pressure Working pressure values ranging from 10.3 MPa to 103.4 MPa (1500 psi to 15,000 psi). NOTE See Table 9.