Jul,01

API RP 577-2004 pdf download

API RP 577-2004 pdf download

API RP 577-2004 pdf download.Welding Inspection and Metallurgy.
1 Scope This recommended practice provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. Common welding processes, welding procedures, welder qualifications, metallurgical effects from welding, and inspection techniques are described to aid the inspector in fulfilling their role implementing API 510, API 570, API Std 653 and API RP 582. The level of learning and training obtained from this document is not a replacement for the training and experience required to be an American Weld- ing Society (AWS) Certified Welding Inspector (CWI). This recommended practice does not require all welds to be inspected; nor does it require welds to be inspected to spe- cific techniques and extent. Welds selected for inspection, and the appropriate inspection techniques, should be determined by the welding inspectors, engineers, or other responsible personnel using the applicable code or standard. The impor- tance, difficulty, and problems that could be encountered dur- ing welding should be considered by all involved. A welding engineer should be consulted on any critical, specialized or complex welding issues. 2 References 2.1 CODES AND STANDARDS The following codes and standards are referenced in this recommended practice. All codes and standards are subject to periodic revision, and the most recent revision available should be used.
3.6 arc welding (AW): A group of welding processes that produces coalescence of work pieces by heating them with an arc. The processes are used with or without the application of pressure and with or without filler metal. 3.7 autogenous weld: A fusion weld made without filler metal. 3.8 back-gouging: The removal of weld metal and base metal from the weld root side of a welded joint to facilitate complete fusion and complete joint penetration upon subse- quent welding from that side. 3.9 backing: A material or device placed against the back- side of the joint, or at both sides of a weld in welding, to sup- port and retain molten weld metal. 3.10 base metal: The metal or alloy that is welded or cut. 3.11 bevel angle: The angle between the bevel of a joint member and a plane perpendicular to the surface of the member. 3.12 burn-through: A non-standard term for excessive visible root reinforcement in a joint welded from one side or a hole through the root bead. Also, a common term used to reflect the act of penetrating a thin component with the weld- ing arc while hot tap welding or in-service welding. 3.13 constant current power supply: An arc welding power source with a volt-ampere relationship yielding a small welding current change from a large arc voltage change. 3.14 constant voltage power supply: An arc welding power source with a volt-ampere relationship yielding a large welding current change from a small voltage change. 3.15 crack: A fracture type discontinuity characterized by a sharp tip and high ratio of length and width to opening dis- placement. 3.16 defect: A discontinuity or discontinuities that by nature or accumulated effect (for example total crack length) render a part or product unable to meet minimum applicable acceptance standards or specifications. The term designates rejectability. 3.17 direct current electrode negative (DCEN): 3.21 filler metal: The metal or alloy to be added in mak- ing a welded joint. 3.22 fillet weld size: For equal leg fillet welds, the leg lengths of the largest isosceles right triangle that can be inscribed within the fillet weld cross section. 3.23 fusion line: A non-standard term for weld interface. 3.24 groove angle: The total included angle of the groove between workpieces. 3.25 heat affected zone (HAZ): The portion of the base metal whose mechanical properties or microstructure have been altered by the heat of welding or thermal cutting. 3.26 heat input: the energy supplied by the welding arc to the workpiece. Heat input is calculated as follows: heat input = (V × i)/60v, where V = voltage, i = amperage, v =weld travel speed (in./min.) 3.27 hot cracking: Cracking formed at temperatures near the completion of solidification 3.28 inclusion: Entrapped foreign solid material, such as slag, flux, tungsten, or oxide. 3.29 incomplete fusion: A weld discontinuity in which complete coalescence did not occur between weld metal and fusion faces or adjoining weld beads. 3.30 incomplete joint penetration: A joint root condi- tion in a groove weld in which weld metal does not extend through the joint thickness.

Download
The previous

API RP 85-2003 pdf download

The next

API RP 945-2003 pdf download

Related Standards